1 ftr-k1 series ?? features ? ? spst 20a and #250 tab terminal type is also available ? ? low coil power (780mw) ? ? type of service: continuous duty ? ? cadmium free contacts ? ? safety standards ul, csa, vde,cqc approved ? ? rohs compliant please see page 7 for more information actual marking does not carry the type name : "ftr" e.g.: ordering code: ftr-k3ab012w actual marking: k3ab012w power relay 1 pole - 20a heavy load ftr-k3 series (a) relay type ftr-k3: ftr-k3 series (b) contact con guration a : 1 form a (spst-no) (pcb terminal) j : 1 form a (spst-no) (tab terminal) (c) coil type b : standard type (780mw) (d) coil rated voltage 012 : 5....48vdc coil rating table at page 3 (e) contact material w : agsno 2 (f) option ls : improved spacing iec60950-1, clearance 8mm ?? partnumber information ftr-k3 j b 012 w - ls [example] (a) (b) (c) (d) (e) (f )
2 ftr-k1 series ?? specification item ftr-k3 contact data con guration 1 form a construction single material agsno 2 resistance (initial) max. 100mohm at 1a, 6vdc contact rating 20a, 250vac (resistive) max. carrying current 25a max. switching current *1 25a max. switching voltage 250vac max. switching power 6,250va min. switching load *2 100 ma, 5vdc life mechanical min. 2 x 10 6 operations electrical resistive load min. 100 x 10 3 operations motor load min. 200 x 10 3 operations inverter load min. 30 x 10 3 operations coil data rated power (at 20 c) 780 mw operate power (at 20 c) 380 mw operating temperature range -40 c to +60 c (no frost) timing data operate (at nominal voltage) max. 20ms (no diode, without bounce) release (at nominal voltage) max. 10ms (no diode, without bounce) insulation resistance (initial) min. 1,000mohm at 500vdc dielectric strength open contacts 1,000vac (50/60hz) 1min contacts to coil 5,000vac (50/60hz) 1min surge strength coil to contacts 8,500v / 1.2 x 50 s standard wave clearance/creepage distance 6.4/9.5mm (8/9.5mm -ls version) other vibration resistance misoperation 10 to 55hz double amplitude 0.7 mm endurance 10 to 55hz double amplitude 1.5 mm shock misoperation min. 100m/s2 (11 1ms) endurance min. 1,000m/s2 (6 1ms) weight approximately 25 g sealing flux proof, rtii * 1 need to consider the heat from pcb when max. current is more than 10a * 2 minimum switching loads mentioned above are reference values. please perform the con rmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. ftr-k3 series
3 ftr-k1 series ?? coil rating type compliance contact rating ul ul 508 e63614 flammability: ul 94-v0 (plastics) 20a, 277 vac (resistive) 1 hp, 125vac 2 hp, 277vac, 100,000 ops. csa c22.2 no. 14 lr 40304 vde 0435 / din en61810-1 40011330 25a, 250vac, cos 1 ; 100k ops. (600 ops/h) cqc 04001009179 20a, 250vac semko 609240: en61058-1: 1992 and a1 en61095: 1993 and a1+a11 5e4: 20a, 15e3: 20/200a, 1e5: 20 (13, 33a) 40t60 ?? safety standards ftr-k3 series coil code rated coil voltage (vdc) coil resistance +/- 10% (ohm) must operate voltage (vdc) * must release- voltage (vdc) * max. coil voltage (vdc) ** rated power (mw) 005 5 32 3.5 0.5 9 780 006 6 46 4.2 0.6 10.8 009 9 105 6.3 0.9 16.2 012 12 185 8.4 1.2 21.6 018 18 415 12.6 1.8 32.4 024 24 740 16.8 2.4 43.2 048 48 2,955 33.6 4.8 86.4 complies with nemko, demko, fimko note: all values in the table are valid for 20c and zero contact current. * speci ed operate values are valid for pulse wave voltage. ** speci ed at 0a contact current at 20c t amb.
4 ftr-k1 series ?? characteristic data ftr-k3 series ?? reference data
5 ftr-k1 series ftr-k3 series
6 ftr-k1 series ftr-k3 series ?? dimensions ?? dimensions ftr-k3 jb type ?? schematics (bottom view) ? ? pc board mounting hole layout (bottom view) unit: mm ?? dimensions ftr-k3 ab type ?? schematics (bottom view) ? ? pc board mounting hole layout (bottom view) unit: mm
7 ftr-k1 series 1. general information ? all signal and power relays produced by fujitsu components are compliant with rohs directive 2002/95ec including amendments. ? cadmium as used in electrical contacts is exempted from the rohs directives on october 21st, 2005. (amendment to directive 2002/95/ec) ? lead free solder plating on relay terminals is sn-3.0ag-0.5cu, unless otherwise speci ed. this material has been veri ed to be compatible with pbsn assembly process. 2. recommended lead free solder pro le ? recommended solder sn-3.0ag-0.5cu. rohs compliance and lead free information 3. moisture sensitivity ? moisture sensitivity level standard is not applicable to through hole mounted electromechanical relays, unless otherwise indicated. 4. tin whiskers ? dipped snagcu solder is known as presenting a low risk to tin whisker development. no considerable length whisker was found by our in house test. we highly recommend that you con rm your actual solder conditions flow solder condition: pre-heating: maximum 120 ? c soldering: dip within 5 sec. at 260 ? c solder bath solder by soldering iron: soldering iron temperature: maximum 360 ? c duration: maximum 3 sec. ftr-k3 series
8 ftr-k1 series japan fujitsu component limited gotanda-chuo building 3-5, higashigotanda 2-chome, shinagawa-ku tokyo 141, japan tel: (81-3) 5449-7010 fax: (81-3) 5449-2626 email: promothq@ft.ed.fujitsu.com web: www.fcl.fujitsu.com north and south america fujitsu components america, inc. 250 e. caribbean drive sunnyvale, ca 94089 u.s.a. tel: (1-408) 745-4900 fax: (1-408) 745-4970 email: components@us.fujitsu.com web: http://us.fujitsu.com/components europe fujitsu components europe b.v. diamantlaan 25 2132 wv hoofddorp netherlands tel: (31-23) 5560910 fax: (31-23) 5560950 email: info@fceu.fujitsu.com web: emea.fujitsu.com/components/ asia paci c fujitsu components asia ltd. 102e pasir panjang road #01-01 citilink warehouse complex singapore 118529 tel: (65) 6375-8560 fax: (65) 6273-3021 email: fcal@fcal.fujitsu.com web: http://www.fujitsu.com/sg/services/micro/components/ fujitsu components international headquarter of ces ?2011 fujitsu components europe b.v. all rights reserved. all trademarks or registered trademarks are the property of their re spective owners. the contents, data and information in this datasheet are provided by fujitsu component ltd. as a service only to its user and o nly for gen- eral information purposes. the use of the contents, data and information provided in this datasheet is at the users? own risk. fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehen- sive, complete and up to date. fujitsu components europe b.v. and af liated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data , and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness t hereof. nor do fujitsu components europe b.v. and af liated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantab ility or tness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, rel iability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. rev. january 20, 2011 ftr-k3 series
|
